> Inderm Basic Plus - instructions

Next -->
Prior to using the Inderm Basic Plus carefully read all instructions. Remove the Inderm from the canvas case and place on a flat surface.
- Changing the Battery -
To charge the Inderm, remove the bottom cap of the Inderm device by rotating it 45 degrees counter clockwise. Unplug the battery from the battery receptacle located at the bottom of the device as shown to the left. Remove the battery by pulling on the 3 prong adaptor, do not pull battery by the wires of the battery itself. Replace the old battery with a fully charged battery. Make sure the 3 prong adaptor snaps into the receptacle on the bottom of the device securely.
- Charging the Battery -
To charge the battery, place the battery in the cradle of the battery charger. Take the 3 prong adaptor (on the battery) and plug it into the battery charging receptacle (shown below with the red arrow) . Then, plug the wall mount adaptor into the backside of the battery charger and plug the other side into a wall outlet. The light on the battery charger will glow red to show that the battery is charging. Over time the light will change to yellow when the battery is at half charge.
- Determining when the Battery is Fully Charged -
When the battery charger light is blinking yellow / green the battery is almost fully charged. When the light turns to solid green the battery is fully charged. While the light glows solid green, the battery may be removed from the battery charger and then plugged back into the Inderm device.
- Syringe Cradle -
The syringe cradle is provided in two different offset settings. The Z-shaped cradle is needed for full 10cc syringes. The 10cc syringe will only accommodate an 8cc fill when used with the straight cradle. The straight cradle is used with 1, 3, and 5cc syringes. Depending on the length of the syringe needle, the syringe cradle should be exchanged so that the needle does not protrude beyond the needle guard.
In addition, the depth that the needle will penetrate the skin can be adjusted using the depth-adjusting knob. This adjustment affects how far the needle guard will travel into the housing once activation occurs and thus how deep the needle will penetrate the skin, it will not result in a shift of the needle guard until activation occurs. This depth adjustment can be viewed via a shift of the red indicator located in a transparent window.

To install the syringe cradle, first unscrew the mounting screw from the syringe cradle. Then place the syringe cradle on the cradle mounting bracket and tighten the mounting screw.

Above the wheel, on the top of the device, is a clear window with a red indicator inside, this indicates the approximate depth of the needle guard as there will not be a visible shift of the needle guard. The needle guard has a depth adjustability of over a half an inch.
  1 2 Next -->
 


To place an order, print out our quick order form and fax your order to 949.458.7416, print form>>, or give us a call to place your order over the phone: toll free at 877.779.9492 or for orders outside the US call 949.458.1897.

 
 

 

Links:
 








Subscribe!
Join our mailing list for exciting new products, special offers and
upcoming events
click to join>>

Order!
To place an order print out our quick order form and fax your order to 949.458.7416
print form >>


How Can We Help? Questions?
Contact Us Today!
Call: 877.779.9492

*Special Pricing
*Promotional Offers
*Package Deals
*Product Information

*Technical Support
*Reorders
*Customer Service
*Billing


Innovative Med Inc.
Tel: 949.458.1897
Toll Free: 877.779.9492
Fax: 949.458.7416
Email: info@imibeauty.com

Global Headquarters:
4 Autry
Irvine, California 92618
U.S.A.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 
 
Can't find what your looking for, seach within our site using yahoo search:
HOME     ORDER     CONTACT US      LINKS     SITE MAP     TERMS & CONDITIONS

Copyright © 2000-2010 Innovative Med Inc. All rights reserved.